Cover Image

QR Code

Literature review: Development of a Speed Limit expert system (PM-LIMITS) for Federal trunk roads in Peninsular Malaysia Final report

Corporate Authors:	Malaysia Jabatan Kerja Raya Cawangan Pakar & Kejuruteraan Awam, Kumpulan IKRAM Sdn Bhd
Published:	Kuala Lumpur CPKA, Jabatan Kerja Raya 2004
Subjects:	Speed limits > Malaysia

Similar Items

Guidelines for the selection of speed limit
Published: (2016)

Speed Limits New Zealand Version 1 User Manual
Published: (1997)

Vlimits : An Expert System speed Zone Advisor The First Three Years ARR 236
Published: (1992)

Speeds, Friction Factors and Alignment Design Standards ARR 154
Published: (1988)

Use of conventional touch voltage limits - Application guide
Published: (2007)

Limits of mator vehicle sizes and weights
Published: (1989)

Noise and vibration from high-speed trains edited by V.V. Krylov.
Published: (2001)

Lapuran khas cadangan kenaikan had laju kenderaan perdagangan
Published: (1987)

British Standard : Harmonized System Of Quality Assessment For Electronic Components : Sectional Specification : Surge Suppression Varistors BSI 1988
Published: (1988)

Standard test method for measuring the p-wave speed and the thickness of concrete plates using the impact-echo method
Published: (2015)

Speed Limits New Zealand Version 1 User Manual
Published: (1997)

Review of road vehicle limits vehicles using Australian Roads
Published: (1983)

Plain limit gauges limits and tolerances
Published: (1953)

Maximum road speed limiters for motor vehicles Part 1. Specification for installed requirements
Published: (1987)

Maximum road speed limiters for motor vehicles part 2. Specification for system and component requirements
Published: (1989)

Vehicle Limits for : Road Safety and Road Protection.
Published: (1974)

Vehicle Limits for : Road Safety and Road Protection.
Published: (1974)

Limit analysis and soil plasticity by Wai-Fah Chen
by: Chen, Wai-Fah 1936-
Published: (1975)

Limit state design Gordon M. Rose
by: Rose, Gordon M.
Published: (1976)

ISO limits and fits Part 1. General, tolerances and deviations Sec 1.2 Tables of commonly used tolerance grades and limit deviations for holes and shafts
Published: (1990)

Vlimits : An Expert System speed Zone Advisor The First Three Years ARR 236
Published: (1992)

Limit states design of structural steelwork David Nethercot
by: Nethercot, D. A. (David Arthur)
Published: (1986)

Oral literature of Indonesia edited by Subagio Sastrowardoyo, Sapardi Djoko Damono, A. Kasim Achmad
Published: (1985)

Specification for screw gauge limits and tolerances Part 4. Limits of size for gauges for screw threads of unified form diameters 1/4 in. and larger
Published: (1964)

Cable trunking. Steel underfloor (duct) trunking
Published: (1973)

Limit-state design of reinforced concrete by A. L. L. Baker
by: Baker, Arthur Lempriere Lancey
Published: (1970)

Hume Industries(Far East)limited concrete pipes catalogue
Published: (1983)

Hume industries(far east)limited Concrete pipes catalogue
Published: (1983)

ISO limits and fits Part 1. General, tolerances and deviations Sec 1.1 Specification for bases of tolerances, deviations and fits
Published: (1990)

Vlimits : An Expert System For Speed Zone Determination In Victoria ARR 155
Published: (1988)

Vlimits : An Expert System For Speed Zone Determination In Victoria ARR 155
Published: (1988)

Specification for radio interference limits for electrical appliances
Published: (1972)

Detrimental Effects of Lateral Soil Movements on Pile Behaviour
by: Ong, D.E.L

Specification for screw gauge limits and tolerances Part 1. Gauges for screw threads of united form
Published: (1960)

Directory for S & T expert
Published: (2005)

ISO limits and fits Part 4. Specification for system of cone ( taper ) fits for cones from C = 1 : 3 to 1 : 500, lengths from 6mm to 630mm and diameters up to 500mm
Published: (1985)

ISO limits and fits Part 5. Specification for system of cone tolerances for conical work pieces from C = 1 : 3 to 1 : 500 and lengths from 6mm to 630mm
Published: (1988)

Cable trunking. Specification for cable trunking made of insulating material
Published: (1982)

Drafting Specification baesd on limiting the number of defectives permitted in small sampels
by: Dudding , B.P
Published: (1955)

Specification for limits and methods of measurement of radio interference characteristics of fluorescent lamps and luminaries
Published: (1988)